Material Selection & RFQ Guide

420 vs 304 Stainless Steel

420 and 304 sit in different stainless families and are purchased for different reasons. 420 is selected when hardness, wear resistance, and edge retention matter—often after heat treatment. 304 is selected when general corrosion resistance, formability, and welded fabrication drive reliability and total installed cost. This guide helps procurement teams translate those differences into a clean RFQ and a defensible material choice.

Martensitic vs austenitic Heat treat & hardness Corrosion & staining Magnetism RFQ checklist
Concerned about corrosion in service? Use PREN to screen families (where applicable), then lock finish and cleanability for real-world outcomes.
Open PREN Calculator

Typical supply forms from XRTGSteel: sheet/plate, coil, pipe/tube, and precision strip.

Audience: Procurement, engineering, QA • Focus: hardness vs corrosion trade-offs • Outcome: selection matrix + RFQ checklist
Rule-of-thumb If your part needs edge retention, wear resistance, or high hardness after heat treatment, shortlist 420. If your part needs forming, welding, and reliable corrosion resistance for general industrial environments, shortlist 304. If chlorides are significant, evaluate whether 304 is sufficient or whether an upgrade (e.g., 316-family) is required.

Contents

1Alloy family overview 2Mechanical properties & hardness 3Corrosion and staining behavior
4Machining, forming, welding 5Magnetism 6Selection matrix
7RFQ checklist 8FAQ

1) Alloy family overview

The fastest way to avoid an incorrect substitution is to recognize the stainless family:

  • 420 is a martensitic stainless steel. It is designed to be heat treated to higher hardness, supporting wear resistance and edge performance.
  • 304 is an austenitic stainless steel. It is designed for general corrosion resistance, formability, and weldability in a wide range of fabricated products.

For broader grade context, see: Stainless Steel Grades Overview.

Stainless steel coil for processing programs
304 is widely supplied in coil programs to support slitting and cut-to-length with consistent surface condition.
Steel blanks and machined parts ready for processing
Machined parts and blanks are typical use cases for martensitic grades where hardness and wear performance are required. Image: Wikimedia Commons (for illustration). Source

2) Mechanical properties & hardness (where 420 wins)

420 is commonly specified because it can be heat treated to higher hardness levels than 304. This makes it a practical choice for components that see abrasive wear, repeated contact, or the need for edge retention.

Procurement implications

  • Specify condition clearly: annealed vs hardened/tempered condition (and target hardness range if applicable).
  • Align inspection: hardness testing requirements and acceptance criteria should be in the RFQ.
  • Plan for distortion: heat treatment can change dimensions—tolerances and post-processing should be planned early.

3) Corrosion and staining behavior (where 304 wins)

304 is the default grade for many fabricated products because it typically provides stronger general corrosion resistance and better appearance retention in everyday environments. 420 can perform well when kept clean and properly finished, but it is generally more sensitive to staining/corrosion in aggressive conditions—especially where chlorides, deposits, or poor drainage are present.

If your problem is “rust” on stainless Stainless can stain or rust under real service conditions (chlorides, deposits, embedded iron, crevices). Grade matters, but finish and contamination control matter too. See: Can Stainless Steel Rust? Causes & Prevention

If the environment includes significant chlorides (coastal exposure, salt splash, washdown), 304 may need an upgrade to a molybdenum-bearing grade family. Reference: 304 vs 316 Selection Guide and the PREN Calculator.

4) Machining, forming, welding

420

  • Often used in machined parts and wear components; machining behavior depends on condition (annealed vs hardened).
  • Heat treatment can be integral to achieving final properties—define route and acceptance criteria early.
  • Welding requires careful procedure control, and post-weld heat treatment may be relevant depending on service and design.

304

  • Excellent for forming and welded fabrication (tanks, frames, housings, architectural components).
  • Commonly available in many finishes; define finish using the Surface Finish Chart.
  • Best practice: manage contamination and post-weld cleaning where corrosion margin is important.

5) Magnetism

Magnetism is primarily a stainless-family characteristic:

  • 420 is typically magnetic (martensitic).
  • 304 is typically non-magnetic in solution-annealed condition; cold work can introduce slight magnetism.

6) Selection matrix (typical industrial choices)

Application / requirementTypical shortlistSpecification notes
Blades, cutting edges, wear parts420Specify heat treatment condition and target hardness; define inspection requirements.
General fabrication: tanks, housings, frames304Define finish, tolerances, and post-weld cleaning expectations if corrosion margin matters.
Cosmetic/appearance-critical fabricated components304Specify finish (No.4/HL/BA) and protective film; confirm packaging.
Washdown/coastal/chloride splash dutyOften 316-family (not 420)Use PREN screening and design for drainage/cleanability; avoid crevices and deposits.

7) RFQ checklist (to get comparable quotes)

  1. Grade + standard: 420 or 304 plus required standard system (ASTM/EN/JIS).
  2. Condition: for 420 specify annealed vs hardened/tempered; include target hardness if required.
  3. Product form: sheet/plate, coil, pipe/tube, strip.
  4. Dimensions & tolerances: thickness/width/length; reference Dimensional Tolerance Tool.
  5. Surface finish: 2B/BA/No.4/HL/mirror; specify Ra if critical; use Finish Chart.
  6. Service environment: chlorides, temperature range, cleaning regime, wear mechanism.
  7. Documentation: MTC/EN 10204 3.1, heat number traceability, hardness report (for 420), PMI if required.
  8. Packaging & delivery: export packing and protection for finish; see Export Packing.

Need a 420 or 304 quote with processing options?

Send grade, standard, condition (for 420), dimensions, finish, quantity, and service environment. XRTGSteel can quote supply forms and processing aligned to your fabrication route.

8) FAQ

Can 420 replace 304 if I need “stainless” parts?

Only if the environment is compatible. 420 is selected for hardness and wear; 304 is selected for corrosion resistance and fabrication. If corrosion margin and appearance retention are priorities, 304 is usually the safer default.

Is 420 always harder than 304?

In heat-treated condition, 420 can reach much higher hardness. In annealed condition, the difference may be less dramatic. That is why specifying “condition + hardness range” is critical when buying 420.

What should I do if the environment includes salt or chlorides?

Evaluate whether 304 is sufficient or whether a 316-family grade is required. Use PREN as a screening tool and specify finish/cleanability controls.

Industry references (official / non-competitor)

Disclaimer: This page supports procurement and early engineering selection. Final material selection should be validated against applicable standards, codes, heat-treatment practice, and service environment by qualified professionals.

Request a Quote Online 24/7/365

Scroll to Top

Contact Us

\n